涩老板在线免费视频_午夜成人精品_神马理论午夜,,_亚洲有薄码区久久欧美精品一区_97人人色_神马在线精品_成人熟女一区二区_亚洲二区三区四区_人妻午夜免费_大鸡巴猛男爆操骚逼国产一区二区_丁香婷婷久久一区二区三区_岛国内射美女_亚洲一级电影,亚洲欧美日韩国产最新版,亚洲五月综合缴情综合久久本,少妇色情喷水又紧又爽小说,巜上司的少妇的滋味,国产精品三级女人国产香蕉,亚洲最好的免费电影,欧美亚洲国产成人精品,国产永久一区二区三区,亚洲综合一区无码精品,歳の熟女セックス,内射带小孩熟妇,果冻传媒在线看免费视频观看,成人欧美一区二区三区片,亚洲 片内射欧美美妇,一本无码人妻在中文字幕免费,亚洲无毛视频,中文字幕丰满孑伦无码专区,亚洲爆乳无码专区色戒纶理,肉乳床欢无码片动漫软件,欧美日韩一区二区另类,久热只有精品在线直播,精品亚洲一区二区在线播放,精品国产乱码久久久久久影片,国产一级高清在线观看,国产精品福利在线一区,成人动漫下载,乱伦性爱视频,xo无码AV毛,国产黄A片免费网站免费,日韩欧美一级特黄特色大片

Whether the joint connection of ventilation pipe is successful or not is the key to the successful installation of the whole ventilation pipe system. If the joint connection of ventilation pipe is not qualified, it will cause the leakage of the pipe system in the process of use. Therefore, when the joint connection of ventilation pipe is carried out, we must pay attention to the following precautions.

1、矩形風管直管段，不管是同一板材連接，還是幾塊板材組合拼接，表面需平整、角線順直。組合前應清除板材切口表面的切割粉末、灰塵及雜物。

1. Whether the straight section of rectangular duct is connected by the same plate or assembled by several plates, the surface shall be smooth and the corner line shall be straight. Before combination, the cutting powder, dust and sundries on the cutting surface of the plate shall be removed.

2、管段組合后45度角切邊外部接縫，需貼鋁箔膠帶封合板材外殼面，每邊寬度不少于20mm.用角尺、鋼卷尺檢查調整垂直度及對角線偏差，并符合規范要求。

2. After the pipe section is assembled, the outer joint of 45 degree angle trimming shall be sealed with aluminum foil tape, and the width of each side shall not be less than 20 mm. The perpendicularity and diagonal deviation shall be checked and adjusted with angle ruler and steel tape, and shall meet the specification requirements.

3、風管的圓弧面或折線面完成下料并折壓成型后，應與平面板預組合無誤后在涂刷粘合劑，以保證管件的幾何形狀尺寸及觀感。

3. After the arc surface or broken line surface of the air duct is cut and folded, it should be pre assembled with the plane plate and then coated with adhesive to ensure the geometric size and appearance of the pipe.

4、連接組合后的管段應垂直擺放至定型后方可移動。

4. After connecting and assembling, the pipe section shall be placed vertically until it is shaped before moving.

5、鋁箔復合保溫風管所用粘合劑須按板材廠商認定的專用粘合劑，如另行采購粘合劑，建議做連接效果對比試驗，并經監理、板材商檢查、認可后方可使用。

5. The adhesive used for the aluminum foil composite insulation duct shall be the special adhesive recognized by the sheet manufacturer. If the brand adhesive is purchased separately, the connection effect comparison test must be conducted, and it can only be used after being inspected and approved by the supervisor and the sheet manufacturer.

6、粘結前須預組合，檢查接縫全部貼合無誤再涂刷粘合劑，粘合時間控制與季節、溫度及粘合劑性能有關。批量加工前應作樣板試驗，確定粘合時間。

6. Before bonding, it is necessary to pre assemble, check that all joints fit correctly, and then brush the adhesive. The bonding time control is related to season, temperature and adhesive performance. Sample test should be done before batch processing to determine the bonding time.